This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
informatica:hp_z230t_400wb_topspin327 [2019/08/14 17:04] miquel [Compilació dels programes AU] |
informatica:hp_z230t_400wb_topspin327 [2019/08/19 17:41] miquel [Problemes amb l'IconNMR (xwish3)] |
||
---|---|---|---|
Line 681: | Line 681: | ||
i podria apuntar a que manca algun compoment d' | i podria apuntar a que manca algun compoment d' | ||
+ | |||
+ | Instal·lo alguns paquets relacionats amb OpenORB/ | ||
+ | |||
+ | * libomniorb4-2: | ||
+ | * libomnithread4: | ||
+ | * libomnithread4-dev: | ||
+ | * The following additional packages will be installed: libdpkg-perl libfile-fcntllock-perl pkg-config | ||
+ | * libcos4-2: | ||
+ | |||
+ | però no resolen el problema, o sigui que caldrà seguir investigant. | ||
+ | |||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | ===== Java JAR Depdendencies ===== | ||
+ | |||
+ | Cal instal·lar el paquet | ||
+ | * default-jdk-headless | ||
+ | per tenir accés al programa '' | ||
+ | |||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | |||
+ | |||
+ | ===== Problemes amb la compilació dels programes AU ===== | ||
+ | |||
+ | Primer error: | ||
+ | |||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | < | ||
+ | # cd / | ||
+ | # nl -ba features.h | sed -n 300, | ||
+ | 301 | ||
+ | | ||
+ | | ||
+ | 304 # ifndef _SYS_CDEFS_H | ||
+ | | ||
+ | 306 # endif | ||
+ | 307 | ||
+ | | ||
+ | | ||
+ | 310 # if defined __USE_FILE_OFFSET64 && !defined __REDIRECT | ||
+ | |||
+ | # locate cdefs.h | ||
+ | / | ||
+ | / | ||
+ | |||
+ | # apt install libc6-dev: | ||
+ | Reading package lists... Done | ||
+ | Building dependency tree | ||
+ | Reading state information... Done | ||
+ | The following additional packages will be installed: | ||
+ | linux-libc-dev: | ||
+ | Suggested packages: | ||
+ | glibc-doc: | ||
+ | The following NEW packages will be installed: | ||
+ | libc6-dev: | ||
+ | 0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded. | ||
+ | Need to get 6,378 kB of archives. | ||
+ | After this operation, 39.5 MB of additional disk space will be used. | ||
+ | Do you want to continue? [Y/n] | ||
+ | Get:1 http:// | ||
+ | [...] | ||
+ | Setting up libc6-dev: | ||
+ | # | ||
+ | </ | ||
+ | |||
+ | |||
+ | ==== Configuració de LD_LIBRARY_PATH | ||
+ | |||
+ | Few hints: | ||
+ | |||
+ | Use the ldconfig command to show the dynamic linker/ | ||
+ | | ||
+ | |||
+ | The ldd paths are set in /// | ||
+ | |||
+ | If your libraries are not on standard path then either you need to add them to the path or add non-standard path to LD_LIBRARY_PATH | ||
+ | | ||
+ | Once you done any one of above things then you need to update the dynamic linker run-time binding by executing below command: | ||
+ | sudo ldconfig | ||
+ | |||
+ | Per més informació consultar: | ||
+ | |||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ==== Undefined ' | ||
+ | |||
+ | FIXME aquesta secció cal moure-la a la pàgina correcta, però per ara la deixo aquí | ||
+ | |||
+ | For problems related to **undefined ' | ||
+ | |||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | The fix is to insert an include definition for the // | ||
+ | |||
+ | <file c> | ||
+ | ... | ||
+ | #include < | ||
+ | #include < | ||
+ | |||
+ | / | ||
+ | * MCE - 20190817 | ||
+ | * | ||
+ | * Include " | ||
+ | | ||
+ | * | ||
+ | * For additional information read | ||
+ | * https:// | ||
+ | | ||
+ | |||
+ | #include < | ||
+ | |||
+ | #include < | ||
+ | #include < | ||
+ | ... | ||
+ | </ | ||
+ | |||
+ | Algunes comandes útils: | ||
+ | |||
+ | < | ||
+ | # export XWINNMRHOME=/ | ||
+ | # cd $XWINNMRHOME/ | ||
+ | # ./makeau -help | ||
+ | # ./makeau -libraries ./ | ||
+ | # ./makeau -show ./ | ||
+ | # ./makeau -native -show ./ | ||
+ | </ | ||
+ | |||
+ | ==== ld: / | ||
+ | |||
+ | L' | ||
+ | |||
+ | < | ||
+ | # ./makeau -show ./ | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | collect2: error: ld returned 1 exit status | ||
+ | </ | ||
+ | |||
+ | que està causat per //using a older version of ld to link a library that had been built with a newer version// i la solució és //The fix is either to build the library that you want to link with a older version of the binutils suite, or to upgrade ld on the machine that wants to link that library.// | ||
+ | |||
+ | * [[https:// | ||
+ | |||
+ | ==== Multiarchitecture cross-compilation ==== | ||
+ | |||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | |||